Ultrasonic Testing

ULTRASONIC TESTING: LEVEL 1

Welds, Castings, Wrought Products 

Our UT floor operates under an open-door policy, with all courses available at any time to suit your convenience 

Why attend this course? 

This course is a combination of the Ultrasonic Testing Introduction course with appropriate Ultrasonic Testing theory and practical training. This course is ISO 9712 recognized and provides excellent preparation for Ultrasonic Testing Level 1 examinations. It meets in full the training hour requirements as specified by the relevant ISO 9712  documentation. 

Content 

• Ultrasonic testing terminology 
• Basic ultrasonic concepts 
• Ultrasound 
• Principals of ultrasonic testing 
• Flaw detector (operation and use) 
• Defect location and sizing techniques 
• Use of calibration and reference blocks 
• Plotting systems 
• Application of a written instruction 
• Examination of samples, welds, castings and wrought products 
• Report writing and discussion of relevant standards and specifications (BS EN etc.) 

Training and experience hours required for Certification 

Full ISO 9712 certification is only achieved once the required experience is acquired following the completion of the required training hours and passing of the examination: 

Ultrasonic Testing (per sector - Welds, Castings, Wrought Products/Forgings*) 

• Level 1 - 40 training hours and 3 months experience 

*Candidates can complete an additional 3 days training and one day exam to include additional UT sectors ( for example if candidate hold welds and wish to add castings)

Responsibilities of an Ultrasonic Testing Level 1 certified NDT professional 

An individual certified to Ultrasonic Testing Level 1 has demonstrated competence to carry out Ultrasonic Testing according to written instructions and under the supervision of Level 2 or Level 3 personnel. Within the scope of the competence defined on the certificate, Level 1 personnel may be authorized by the employer to perform the following in accordance with Ultrasonic Testing instructions: 

• Set up Ultrasonic Testing equipment 
• Perform Ultrasonic Inspection tests 
• Record and classify results of the tests according to written criteria 
• Report the results of Ultrasonic tests 

Ultrasonic Testing Level 1 certified personnel shall neither be responsible for the choice of test method or technique to be used, nor for the interpretation of the test results.

 ULTRASONIC TESTING: LEVEL 2

Welds, Castings, Forging / Wrought Products 

Our UT floor operates under an open-door policy, with all courses available at any time to suit your convenience

Why attend this course? 

This course is a combination of the UT Introduction course with appropriate Ultrasonic Testing theory and practical training. This course is EN ISO 9712  recognised and provides excellent preparation for Ultrasonic Testing Level 2 examinations. It meets in full the training hour requirements as specified by the relevant I EN ISO 9712 documentation. 

Content 

• Basic concepts 
• Ultrasound 
• Principals of ultrasonic testing 
• Flaw detector (operation and use) 
• Defect location and sizing techniques 
• Use of calibration and reference blocks 
• Plotting systems 
• Examination of samples, welds, castings and wrought products 
• Report writing and discussion of relevant standards and specifications (BS, EN etc) 

Minimum Training and experience hours required 

Full  EN ISO 9712 certification is only achieved once the required experience is acquired following the completion of the required training hours and passing of the examination: 

Ultrasonic Testing (per sector - Welds, Castings, Wrought Products/Forgings*) 

• Level 2 (Level 2 after level 1) - 80 training hours and 9 months experience 
• Level 2 (Direct Level 2 without level 1) - 120 training hours and 12 months experience 

*Candidates can complete an additional 5 day training and one day exam to include additional UT sectors ( for example if candidate hold welds and wish to add castings) 

Ultrasonic Node & Nozzle 

Level 2 - 40 training hours (supplementary to UT Level 2 ) 

Ultrasonic Testing of Wrought plate- including Thickness Gauging 

40 hours training and 3 months experience Direct to Level 2 options are available, in this instance, students would be required to complete both Level 1 and 2 training and experience requirements. 

Responsibilities of an Ultrasonic Testing Level 2 certified NDT professional 

An individual certified to EN ISO 9712 Ultrasonic Testing Level 2 has to have competence to perform Ultrasonic testing in according to UT procedures Within the scope of the competence defined in the certificate.  EN ISO 9712 Level 2 personnel may be authorised by the employer to: 

• Select the Ultrasonic Testing technique for the test method to be used 
• Define the limitations of application of the testing method 
• Translate Ultrasonic Testing codes, standards, specifications and procedures into Ultrasonic Testing instructions adapted to the actual working conditions 
• Set up and verify Ultrasonic Testing equipment settings 
• Perform and supervise Ultrasonic tests 
• Interpret and evaluate results according to applicable standards, codes, specifications or procedures 
• Prepare written Ultrasonic Testing instructions 
• Carry out and supervise all tasks at or below Level 2 
• Provide guidance for personnel at or below Level 2 
• Report the results of Ultrasonic tests.

ULTRASONIC TESTING: LEVEL 3

Why attend this course? 

These are guidance courses aimed at the  EN ISO 9712 requirements for Ultrasonic Practitioner Level 3 in either welds, casting or wrought products. The main objective is to make candidates fully aware of the scope of the examination and level of knowledge required (This will also enable candidates to identify their weak subject areas). Advice will be given on any further tuition required. Candidates should ideally hold a  EN ISO 9712 Level 2 approval in Ultrasonic Testing as a minimum and have at least 3 years experience in NDT Inspection before attempting these courses. 

Candidates are required to complete and pass the  EN ISO 9712 Level 3 Basic training course before attempting individual methods. 

Course Content 

• Terminology and definition of UT 
• Physical principle of the method and associated knowledge 
• Products Knowledge and related capability of the method and derived techniques 
• Equipments 
• Information prior to test 
• Testing techniques 
• Evaluation reporting 
• Assessment, Quality aspects and developments 
• Analysis of procedures 
• Procedure writing 
• Mock examinations

 Basic Examination:

Main Method Examination

Training and experience hours required for Certification 

Full EN ISO 9712 certification is only achieved once the required experience is acquired following the completion of the required training hours and passing of the examination: 

Ultrasonic Testing (per sector - Welds, Castings, Wrought Products/Forgings*) 

• Level 3 -40 training hours (+80 hrs. for Level 3 Basic) and 36 months experience 

*Candidates can complete an additional 4-day training and one day exam to include additional UT sectors (for example if candidate hold welds and wish to add castings) 

Responsibilities of an Ultrasonic Testing Level 3 certified NDT professional 

An individual certified to Ultrasonic Testing Level 3 has demonstrated competence to perform and direct Ultrasonic Testing operators for which he is certified. Ultrasonic Testing Level 3 personnel have demonstrated: 

• The competence to evaluate and interpret results in terms of existing standards, codes, and specifications 
• Sufficient practical knowledge of applicable materials, fabrication, process, and product technology to select Ultrasonic Testing methods, establish Ultrasonic Testing techniques and assist in establishing acceptance criteria where non are otherwise available 
• A general familiarity with other NDT methods 

Within the scope of the competence defined on the certificate, Ultrasonic Testing Level 3 personnel may be authorized to: 

• Assume full responsibility for the test facility or examination center and staff 
• Establish, review for editorial and technical correctness and validate Ultrasonic Testing instructions and procedures 
• Interpret codes, standards, specifications and procedures 
• Designate the particular Ultrasonic test methods, techniques and procedures to be used 
• Within the scope and limitations of any certification held, carry out all tasks at all levels 
• Provide guidance for Ultrasonic Testing personnel at all levels 

Level 3 certified personnel may be authorized to carry out, manage and supervise EN ISO 9712 qualification examinations on behalf of the C-WT. 

Where Level 3 duties require the individual to apply routine NDT by a method or methods within a particular product or industry sector, C-WT strongly recommends that the industry demand that this person should hold and maintain Level 2 certification in the applicable method(s) and sector(s). 

The range and scope of EN ISO 9712 certification available at each level is defined in the relevant appendix to these general requirements.

ULTRASONIC TESTING: REFRESHER / RECERTIFICATION

Why attend this course? 

Ideal for those who already have a basic understanding of the techniques of ultrasonic inspection and would like intensive instruction to improve their knowledge and increase their experience in preparation for a recertification examination. The course is suitable for candidates who are wishing to progress towards any of the ultrasonic examination qualifications and has a high practical content; all equipment is provided. 

Content 

• Revision of basic techniques 
• Probe identification 
• Test sensitivity 
• Equipment checks 
• Geometry/ultrasonic technique selection 
• Defect response 
• Practical exercises on a wide variety of weldments 
• Defect sizing methods 

Candidates have the option of single or multiple days and a flexible option for candidates undertaking ultrasonic training covering both welds, cast or wrought products.

* 18% GST EXTRA